Muzzle brake compensator. These parts are cleaned immediately after shooting. It is recommended to lubricate the weapons graphite grease.
During firing on weapons detail form carbon deposits, which corrodes the chrome plating parts, and this leads to the formation of shells. And the presence of the shells is the formation of additional backlash and clearances, leading to amplification of oscillations during firing and to a deterioration of accuracy battlefield. Besides, pores gun metal from high temperature during firing expand and absorb snuff. Soak up carbon deposits out on the metal surface during 3-4 days after the shooting, and continues to eat away at the details. Therefore, a single brushing after firing insufficiently, arms should be cleaned daily 4 the day after the shooting.
The lateral surface and a threaded muzzle.
It is recommended to clean the gun with soapy water or own saliva, as the deposit has an acidic reaction and dissolves well in these alkaline solutions,. But I want to note, soap and saliva are very weak alkalis. Much better dissolves soot soda solution in water, and, soda is better to take food, and kaltsirovannuyu. In the field at any point of the boiler allowance (simply put, any field kitchen) there are powder “posudomoy”, which includes soda. Dosage for cleaning weapons – 4-5 tablespoons a bucket. If we make the solution in hot water, then it can be cleaned with a weapon, Named from the cold, without waiting, when it otpoteet.
Nagar easily removed conventional cloth immediately after shooting, until the weapon is still warm. therefore, if you can, immediately after the shooting, disassemble the gun and wipe the place of the strongest concentrations of soot: gas chamber, the gas piston, gas pipe and the muzzle brake-compensator.
Gun barrel and the shutter can be left to a more thorough cleaning.
The gas piston.
Lower any dirty item at a time in kerosene, and a touch of rust and soot otkisnet and tender. But, to permanently remove it, required considerable effort.
Often the soldiers to remove the soot and rust using abrasives (sandpaper, crushed brick, etc.), Not understanding, that deal weapon damage -nepopravimy. After all, with such cleaning erased chromium coating, and the metal in these areas merely fade under the influence of high temperature propellant gases.
And there is a readily available abrasive agent, which does not damage chrome. This is a common wood ash. Rastolchite extinct coal into a fine powder and used for cleaning. Best of all ash cleans soot from birch, since it has the most strong alkaline action.
gas tube.
In the heat of battle weapon can overheat and may seize. And it happens quite often. Release of the AKC- 7 43-4 Store consecutive long lines and in the dark, automatic trunk will be illuminated with violet light. It is a sign of overheating. In the daytime, the overheating is much more difficult to notice. To avoid overheating, I advise you to use instead of frequent fire firing single shots or short bursts of long queue 2-3 chuck. Single shots you will achieve a higher accuracy of the battle and avoid overheating.
Well, and if the weapon jammed? Disconnect and store several times distort the bolt carrier, achieving free passage through the movable parts “burnt” a place. If it burned so badly, that the hand can not take back the bolt carrier, Abut the machine into the ground with the butt and slide bolt carrier foot. Just do not forget, that was round in the chamber, do not hit yourself or your friend. And not enough of the hot trunk bare hand, wrap it with something.
And in order to reduce the possibility of seizure of arms from sticking moving parts, I advise you to use a graphite grease armory. It can be found in any armory. It is well withstand high temperatures and prevents fouling a metal vedaniyu. Apply this grease thin layer on the gas piston, side surfaces of the gas lance and the gas chamber, side surface and a threaded muzzle and on a side surface and a threaded muzzle brake compensator.
Gas chamber.
Watch carefully, to this grease was not included in the bore. Even long after the shooting this grease can be easily removed with soot. And the forces of the arms much less is spent cleaning. But do not use this lubricant in the winter. It thickens and may cause delays. In winter, weapons and so rapidly cools and the likelihood of jamming is much less.
Do not forget to clean the inside, lubricate and recharge shops, even if you do not use or pulled from the discharge vest or pouch. The store can be exposed to water or dirt, which will lead to the malfunctioning of its work. Just wipe the top of the store and the feeder is not enough.
Special attention should be given special care of arms, which is intended for the silencer. Design features of the weapons and ammunition cause weaker job automation (due to a weak gas pressure on the shutter when reloading). therefore, to moving parts: silent weapons functioned normally, they need a more thorough cleaning and lubrication.
And one more little trick. In order not to confuse your machine with someone else, Make it a distinctive sign. for example, sticker from tape tape, duct tape or medical patch in a certain place you (on the handguard, fore-end, example, Shoulder, pistol grip). This will allow you to easily locate your machine among others, even in the dark by touch in case of an alarm, shelling, etc..
And it will help in cleaning weapons. Do not forget, one of the strongest disappointment at war: collected weapons, detect, machine that cleaned friend.
